Week 3 · Angular Kinematics

Angular Kinematics: Knee Range of Motion in Gait

Measure the knee joint angle frame by frame during walking, then compute angular velocity, angular acceleration and range of motion across the gait cycle.

Pre-lab ≈ 25 minIn-lab 90 minReport ≈ 90 minTools: camera, Kinovea, Excel

Overview

Last week you tracked one point. This week you track a joint angle formed by two segments. You will record a clean lateral view of a full gait cycle, measure the knee angle in Kinovea, export the angle–time data, and compute angular displacement (θ), angular velocity (ω) and angular acceleration (α) in Excel. The emphasis is on how knee ROM and its timing relate to the phases of gait.

Learning objectives

  1. Use anatomical landmarks to define a sagittal-plane knee angle (thigh–shank).
  2. Distinguish absolute (segment) angles from relative (joint) angles, and included angles from flexion angles.
  3. Compute ω = Δθ/Δt and α = Δω/Δt in Excel and plot each against time.
  4. Identify stance and swing features on the knee-angle curve and compute ROM.
  5. Explain why differentiation amplifies noise and apply at least two strategies to reduce it.
ComponentWhat you doTime
Pre-labAngular units, joint angles, the gait cycle; quiz20–30 min
Lab activityLandmarks, filming walking trials, Kinovea angle tracking, export90 min
Lab reportθ, ω, α graphs, ROM, gait-phase interpretation, discussion≈ 90 min

Pre-Lab Reading ≈ 15 min

1. Angular motion and its units

Angular motion is rotation of a body or segment about an axis. Points farther from the axis travel farther for the same rotation, which is why linear and angular quantities are linked by the radius. Degrees are intuitive for joint angles; radians are required whenever you convert between angular and linear quantities.

1 rev = 360° = 2π rad1 rad ≈ 57.3°
ω = (θ_f − θ_i) / ΔtAngular velocity (deg/s or rad/s)
α = (ω_f − ω_i) / ΔtAngular acceleration (deg/s² or rad/s²)
v = ω · rTangential (linear) velocity; ω in rad/s
a_t = α · rTangential acceleration; α in rad/s²
ROM = θ_max − θ_minRange of motion over a defined window

2. Absolute vs. relative angles

An absolute (segment) angle describes a segment's orientation relative to a fixed reference such as the horizontal (e.g., shank angle). A relative (joint) angle is the angle between two adjacent segments (e.g., thigh and shank = knee angle). Kinovea's angle tool returns the included angle between the two arms: about 180° when the knee is straight. Clinicians report knee flexion, where straight = 0°:

Knee flexion (°) = 180° − included angle

Pick one convention, state it in your report, and use it consistently. Counter-clockwise is positive for absolute angles; for the knee, flexion is positive.

3. Landmarks for the sagittal knee angle

  • Greater trochanter — proximal thigh (hip joint center approximation)
  • Lateral femoral epicondyle — knee joint center (angle vertex)
  • Lateral malleolus — ankle joint center (distal shank)

4. The gait cycle and the knee

A gait cycle (stride) runs from initial contact of one foot to the next initial contact of the same foot. Stance is about 60% of the cycle and swing about 40% in walking. In typical adult walking the knee shows two flexion "waves":

% cycle (approx.)PhaseKnee behaviourTypical flexion
0Initial contactNearly extended≈ 0–5°
0–15Loading responseFlexes to absorb weight acceptance (eccentric quadriceps)≈ 15–20°
15–40Mid → terminal stanceRe-extends toward minimal flexion≈ 3–5°
50–62Pre-swingRapid flexion begins≈ 35–40°
62–75Initial → mid-swingPeak flexion for foot clearance≈ 60–65°
75–100Terminal swingRapid extension for next contact≈ 0–5°

So typical walking knee ROM is roughly 60°. Faster walking increases it; shoe type, pain, and pathology change it.

5. Noise and differentiation (again)

Your angle data contain small clicking errors. ω is the slope of θ; α is the slope of ω. Each step divides by a small Δt and magnifies the error. Good practices: film at the highest frame rate available, use high-contrast landmark markers, track carefully at the fastest part of swing, and smooth before differentiating (a 3–5 point moving average, =AVERAGE(B2:B6)). Central differences, ω_i = (θ_{i+1} − θ_{i−1}) / (t_{i+1} − t_{i−1}), are also less noisy than forward differences.

Interactive: Knee angle → ω → α

A textbook-shaped knee flexion curve with adjustable digitizing error. Find the settings that make α interpretable.

Practice data setWant to practice the Excel steps before lab? Download a sample Kinovea knee-angle export (included angle, time in ms, from a previous lab).

Before you come to lab

  • Wear shorts or fitted pants so the knee and ankle landmarks can be marked on skin or tight clothing.
  • Bring your laptop with Kinovea and your Week 2 Excel file for reference.

Pre-Lab Quiz ≈ 10 min

Which of the following is a relative (joint) angle?
A relative angle is measured between two adjacent segments; the knee angle is thigh–shank.
Kinovea reports an included knee angle of 118°. What is the knee flexion angle?
Flexion = 180° − 118° = 62°, which is typical peak swing flexion.
Where is the vertex of the knee angle placed?
The epicondyle approximates the knee joint center; the arms run to the trochanter (thigh) and malleolus (shank).
When does peak knee flexion occur in walking?
The knee flexes to about 60–65° in early swing to shorten the limb so the foot clears the ground.
The knee angle changes from 20° to 50° in 0.10 s. The average angular velocity is:
ω = (50 − 20)/0.10 = 300 deg/s.
To use v = ω·r, angular velocity must be in:
Radians are dimensionless ratios of arc length to radius, so rad/s × m gives m/s directly.
A gait cycle is defined as:
That is a stride. (b) is a step; (d) is the swing phase.
Which strategy does NOT reduce noise in your angular acceleration curve?
Extra decimal places do not change the measurement error, they only make the noise look more precise than it is.

Short responses (submit to your LMS)

1. Why does the knee flex during loading response, and what would happen to impact forces if it stayed fully extended?

2. Predict where in the gait cycle the magnitude of knee angular velocity |ω| will be largest. Explain your reasoning.

Lab Activity 90 min

📍 Set up for your campusTape an 8–10 m walkway with a plain background and room for a camera 3–4 m to the side, level with the knee.

Group organization

4 teams of 5. Each team films two walkers at two speeds (preferred and fast), 2 trials each. Every student analyzes one trial. Roles: Walker, Landmark marker, Camera operator, Start/stop caller, Recorder.

Equipment per team

  • Camera (≥ 60 fps; 120 fps preferred) + tripod
  • Meter stick for calibration
  • Adhesive markers or tape (3 per walker)
  • 8–10 m walkway with tape start, capture zone, and end marks
  • Laptops with Kinovea and Excel

Timeline

  • 0:00–0:10Landmark palpation demo (greater trochanter, lateral epicondyle, lateral malleolus) and Kinovea angle-tool demo.
  • 0:10–0:20Palpate and mark landmarks on both walkers; set up camera and calibration.
  • 0:20–0:40Record walking trials (2 walkers × 2 speeds × 2 trials).
  • 0:40–1:15Kinovea: calibrate, track the knee angle through one full gait cycle, export CSV.
  • 1:15–1:30Excel start: unit conversion, flexion angle column, θ–t graph; instructor check-off.

Video capture

  1. Camera perpendicular to the walkway, centered on the capture zone, at knee-to-hip height, ~4 m away. Fixed zoom, no panning.
  2. Record the meter stick in the walking plane for calibration.
  3. The walker starts 3–4 steps before the capture zone (so they reach steady speed) and continues 3–4 steps past it.
  4. Make sure at least one complete gait cycle of the near-side leg is visible (initial contact to next initial contact).

Kinovea workflow

  1. File → Open the walking trial. Calibrate with the line tool on the meter stick.
  2. Choose the Angle tool. Place the vertex on the lateral epicondyle, one arm to the greater trochanter, the other to the lateral malleolus.
  3. Step frame by frame from the first initial contact to the next initial contact of the same foot, keeping all three points on the landmarks (enable tracking and correct drift).
  4. Note the frame/time of initial contact, toe-off, and the next initial contact in your notebook.
  5. Right-click the angle → Export → CSV/Spreadsheet. Save as LastName_Walk_KneeAngle.csv.

Lab Report ≈ 90 min

Practice data setAbsent, or your trial failed? Use this simulated data set. It has the same columns as the lab data sheet, so every formula below works unchanged. Tell your instructor in your report that you used it.
⬇ Kinovea knee export, time in ms, included angle

Step 1 — Organize the data ≈ 15 min

ColHeaderFormula (data start row 2)
ATime (s)from export (÷1000 if ms)
BIncluded angle (deg)from export
CKnee flexion θ (deg)=180-B2
DSmoothed θ (deg, 5-pt)=AVERAGE(C2:C6)
EAngular velocity ω (deg/s)=(D3-D2)/(A3-A2)
FAngular acceleration α (deg/s²)=(E4-E3)/(A4-A3)
G% Gait cycle=(A2-$A$2)/$J$2*100

Put your stride time (second initial contact − first initial contact, in s) in cell J2, and start row 2 at the first initial contact.

Step 2 — Graphs ≈ 25 min

  1. Figure 1. Knee flexion angle during walking (θ vs. time or % gait cycle). Use arrows or data labels to mark maximum and minimum flexion, toe-off, and the loading-response peak.
  2. Figure 2. Knee angular velocity (ω vs. time).
  3. Figure 3. Knee angular acceleration (α vs. time).
  4. Figure 4. Speed comparison: overlay preferred and fast walking θ vs. % gait cycle (your trial and a teammate's, same walker).

Step 3 — ROM and key values ≈ 15 min

Table 1: ROM (=MAX(C:C)-MIN(C:C) over one cycle), peak swing flexion (deg and % cycle), loading-response peak flexion, peak |ω| (deg/s and rad/s), stride time, stance %. Then convert peak ω to rad/s and compute the tangential velocity of the ankle using your measured shank length: v = ω·r.

Step 4 — Discussion questions ≈ 35 min

Answer the five required questions. Optional questions earn up to +3 extra-credit points.

  1. Mark on your angle plot the time points of maximum knee flexion and maximum extension. Which gait phases do these correspond to?
  2. Report knee ROM over the cycle you analyzed. How does it compare to the ~60° typical value? Give two reasons yours might differ.
  3. Describe how angular velocity changes across stance vs. swing. Where is |ω| largest and why?
  4. Explain why your angular acceleration plot looks noisier than the angle plot. Which two strategies did you use (or would you use) to reduce apparent noise while preserving real features?
  5. How did walking speed change ROM and peak ω (Figure 4)?

Optional questions (extra credit)

  1. Compare this walking knee-angle curve to last week's CMJ COM displacement curve. Give two similarities and two differences in shape and timing.
  2. Using your calculated ankle tangential velocity, explain why distal segments move faster than proximal ones for the same angular velocity.

Submission checklist

  • Excel workbook with calculations and Figures 1–4.
  • Document: figures with labeled events, Table 1, discussion answers.
  • Video file or Kinovea screenshot showing angle placement.

Grading rubric (50 pts)

CriterionPtsFull credit looks like
Data processing12Correct angle convention, smoothing, ω and α formulas, units
Figures12Four figures, events labeled, % gait cycle normalization
ROM table & tangential velocity8Correct values with radian conversion
Discussion15Correct gait-phase interpretation using your data
Presentation3Professional formatting

References

  • Perry, J., & Burnfield, J. M. (2010). Gait analysis: Normal and pathological function (2nd ed.). SLACK.
  • Winter, D. A. (2009). Biomechanics and motor control of human movement (4th ed.). Wiley.
  • Puig-Diví, A., Escalona-Marfil, C., Padullés-Riu, J. M., Busquets, A., Padullés-Chando, X., & Marcos-Ruiz, D. (2019). Validity and reliability of the Kinovea program in obtaining angles and distances using coordinates in 4 perspectives. PLOS ONE, 14(6), e0216448. doi.org/10.1371/journal.pone.0216448