Linear Kinetics: Friction & Inclined Planes
Tilt a board until a block (or a shoe) starts to slide, resolve its weight into components, and measure the coefficient of friction of different surfaces.
Overview
Kinetics asks why things move: forces. Friction is the force that lets us walk, sprint, cut and stop — and its absence is why we slip. On a slope, weight always acts straight down, but we care about the parts of weight acting along the slope and into it. You will find the angle at which friction can no longer hold a block in place and use it to calculate the coefficient of static friction for several surfaces, including athletic footwear.
Learning objectives
- Draw a free-body diagram of an object on an incline.
- Resolve weight into parallel (F_down) and perpendicular (F_into) components.
- Relate normal force, friction force and the coefficient of friction.
- Measure μs for low-, moderate- and high-friction surfaces and show that μs = tan θ at the point of slipping.
- Apply friction concepts to footwear, surfaces, slips and sport performance.
| Component | What you do | Time |
|---|---|---|
| Pre-lab | Newton's laws, free-body diagrams, incline components, friction; quiz | 20–30 min |
| Lab activity | Baseline block, three surfaces, mass test, shoe-traction test | 90 min |
| Lab report | Force calculations, μ comparisons with error bars, discussion | ≈ 90 min |
Pre-Lab Reading ≈ 15 min
1. Newton's laws in one paragraph
First law (inertia): an object keeps its velocity — including zero — unless a net external force acts. Second law: ΣF = m·a; net force equals mass times acceleration, and this is the bridge from kinematics (Weeks 2–5) to kinetics. Third law: every force has an equal and opposite reaction; push down and back on the ground and it pushes you up and forward (the ground reaction force, GRF).
2. Free-body diagrams
To draw a free-body diagram (FBD): isolate the object, draw every external force as an arrow from its point of application, label each force, then choose axes. On a slope, tilt your axes so x runs along the slope and y runs perpendicular to it. Then only weight needs to be resolved.
3. Weight on a slope
| W = m·g | Weight (N); g = 9.81 m/s² |
| F_down = m·g·sin θ | Component of weight pulling the object down the slope |
| F_into = m·g·cos θ | Component of weight pressing the object into the slope |
| F_normal = F_into | Surface reaction force (Newton's 3rd law), perpendicular to surface |
| F_friction ≤ μs·F_normal | Static friction can grow up to this maximum |
Friction acts parallel to the surface, opposing motion (or attempted motion), but its maximum depends on the perpendicular force pressing the surfaces together.
4. The slip angle and μs
At low angles, static friction exactly matches F_down and the block stays put. As θ rises, F_down grows (sin θ) while F_into shrinks (cos θ), so the friction available shrinks. At the critical angle the block is just about to slip:
m·g·sin θ = μs·m·g·cos θ → μs = tan θ
Mass cancels! In theory the slip angle depends only on the two surfaces, not on how heavy the block is. You will test this. Once sliding, kinetic friction (μk) takes over, which is usually smaller than μs — that is why a slip, once started, is hard to stop.
W = 0.200 × 9.81 = 1.962 N · F_down = 1.962 sin 35° = 1.125 N · F_into = 1.962 cos 35° = 1.607 N
If the block is just about to slip at 35°: F_friction = 1.125 N and μs = 1.125/1.607 = tan 35° = 0.70.
5. Friction in human movement
Required friction in walking is roughly μ ≈ 0.2; cutting and sprint starts demand much more. Shoe outsole material, tread, contaminants (water, dust) and surface type change available friction. Too little causes slips; too much (e.g., some artificial turf with studded shoes) can fix the foot while the body rotates, loading the knee.
Before you come to lab
- Install an inclinometer app (e.g., Phyphox "Inclination" or any level app) on your phone.
- Bring one athletic shoe you are willing to test (clean outsole).
Pre-Lab Quiz ≈ 10 min
Short responses (submit to your LMS)
1. Predict the rank order (lowest to highest μs) of the surfaces you plan to test and justify it.
2. Describe a real-world situation where an athlete or older adult needs more friction and one where too much friction could be harmful.
Lab Activity 90 min
Group organization
4 teams of 5, each with one tilt board. Roles: Tilter (raises the board slowly and steadily), Angle reader (inclinometer), Spotter (calls the instant of slip), Surface manager (swaps and cleans surfaces), Recorder. Rotate each surface.
Equipment per team
- Hinged tilt board (≈ 60–90 cm) or board + books
- Wooden block (≈ 200 g) and added masses
- Kitchen scale (g)
- Phone inclinometer or large protractor
- Surface materials: e.g., wax paper, cardboard, felt, rubber mat, sandpaper, gym flooring sample
- One athletic shoe per student (team tests 3)
Timeline
- 0:00–0:10FBD warm-up on the board; demo of a smooth, slow tilt and how to call the slip.
- 0:10–0:25Activity 1 — Baseline: bare board, 5 trials.
- 0:25–0:55Activity 2 — Three surfaces (predicted low, moderate, high), 5 trials each.
- 0:55–1:10Activity 3 — Does mass matter? Baseline surface with block + 200 g and + 400 g, 3 trials each.
- 1:10–1:25Activity 4 — Shoe traction: three shoes on the gym-floor sample (and wet vs. dry if time), 3 trials each.
- 1:25–1:30Data upload and clean-up.
Procedure for every trial
- Weigh the object and record mass in grams; convert to kg.
- Place the object at the same start mark near the top of the board, flat face down.
- Raise the board slowly (≈ 1–2° per second). Jerky lifting causes early slips.
- Spotter calls "slip" at the first sustained movement. Angle reader records θ at that instant (the angle just below where it moves).
- Reset and repeat. Discard a trial if the object rotates or tips instead of sliding.
Lab Report ≈ 90 min
⬇ Baseline, 3 surfaces, mass test, 3 shoes
Step 1 — Force calculations ≈ 25 min
Columns A–G are the data sheet (D mass in g, F slip angle). Add:
| Col | Header | Formula (row 2, fill down) |
|---|---|---|
| H | Mass (kg) | =D2/1000 |
| I | Weight (N) | =H2*9.81 |
| J | F_down (N) | =I2*SIN(RADIANS(F2)) |
| K | F_into = F_normal (N) | =I2*COS(RADIANS(F2)) |
| L | F_friction at slip (N) | =J2 |
| M | μs | =L2/K2 |
| N | μs check | =TAN(RADIANS(F2)) |
Build a summary table with AVERAGEIFS / STDEV.S for each surface: mean θ, mean μs ± SD.
Step 2 — Required visuals ≈ 20 min
- Figure 1. Free-body diagram of the block at the slip angle for your highest-friction surface, with all four forces labeled with values.
- Figure 2. Scatter plot of F_down vs. μs for the baseline and three surfaces (as in the original Lab 6 handout).
- Figure 3. Column chart of mean μs ± SD (custom error bars) for every surface and shoe.
- Figure 4. Slip angle vs. object mass (Activity 3) with a linear trendline and its equation.
Step 3 — Discussion questions ≈ 40 min
Answer the five required questions. Optional questions earn up to +3 extra-credit points.
- Describe the magnitude of μs for the materials you tested. Were your predictions correct? Explain any surprises in terms of surface properties.
- As μs increased, what happened to the slope angle at which the block began to move? Explain using F_down and F_friction.
- Did adding mass change the slip angle (Figure 4)? Compare to the theory and explain any discrepancy.
- As slope angle θ increases, how do F_weight, F_down, F_into and the maximum F_friction change? Use your data or the interactive tool to support your answer.
- Rank the shoes you tested. Relate the results to outsole material and tread and to the demands of a specific sport.
Optional questions (extra credit)
- In a real-world scenario where you want to maximize speed down a hill (e.g., downhill skiing), which variables could you manipulate, and how?
- In a scenario where you want to prevent movement down a slope (e.g., preventing slips on a wet ramp), which variables could you manipulate, and how?
- Identify the largest source of error in determining the slip angle and propose an improvement.
Submission checklist
- Excel workbook with all trials, summary table and Figures 2–4.
- Document: FBD (Figure 1), all figures with captions, discussion answers.
Grading rubric (50 pts)
| Criterion | Pts | Full credit looks like |
|---|---|---|
| Calculations | 12 | Radians handled, μs from forces matches tan θ, means ± SD |
| FBD & figures | 14 | Correct FBD; error bars; trendline |
| Discussion | 20 | Applies friction physics to human movement with data |
| Presentation | 4 | Professional and complete |
References
- Urone, P. P., & Hinrichs, R. (2022). College physics 2e. OpenStax. openstax.org (CC BY 4.0) Chapters 4–5 (Newton's laws, friction).
- Redfern, M. S., Cham, R., Gielo-Perczak, K., Grönqvist, R., Hirvonen, M., Lanshammar, H., Marpet, M., Pai, C. Y.-C., & Powers, C. (2001). Biomechanics of slips. Ergonomics, 44(13), 1138–1166. doi.org/10.1080/00140130110085547