Week 7 · Metabolic Testing

Graded Exercise Test: VO₂max & Ventilatory Thresholds

Last week you predicted VO₂max from a run. This week you measure it. Volunteers complete a graded treadmill test while a gas analyzer measures every breath, and the class uses the data to find VO₂max, the two ventilatory thresholds, and how closely the ACSM equations predict real oxygen cost.

Pre-lab ≈ 45 minIn-lab 75 minNotebook ≈ 60 minTools: VO₂-only analyzer or metabolic cart, HR straps, treadmill

Overview

A graded exercise test (GXT) with gas analysis is the reference method for cardiorespiratory fitness. Workload rises step by step while the analyzer measures oxygen uptake (VO₂) and ventilation (VE). From that one test you get VO₂max, two ventilatory thresholds (VT1 and VT2) that define training zones, and the oxygen cost of each submaximal speed.

Learning objectives

  1. Calibrate and fit a metabolic analyzer and run a graded treadmill test safely.
  2. Apply VO₂max criteria (plateau, HR, RPE, and RER when CO₂ is measured).
  3. Identify VT1 and VT2 from ventilatory data and convert them to heart-rate training zones.
  4. Compare measured submaximal VO₂ with the ACSM walking and running equations.
  5. Compare measured VO₂max with the Week 6 field-test predictions for the same people.
Your equipmentWhat you can measure this week
VO₂-only analyzer (e.g., VO2 Master) + HR strapVO₂, VO₂max and plateau, VE, breathing rate and tidal volume, VT1 and VT2 from ventilation, HR zones, economy
Full metabolic cart (O₂ + CO₂)All of the above, plus VCO₂, RER (fuel use and the RER ≥ 1.10 criterion), and thresholds from the ventilatory equivalents for both gases
No analyzerRun the same protocol with HR and RPE, and analyze the backup data set (two participants, cart-style columns)
ComponentWhat you doTime
Pre-lab readingBackground, interactive tool and one research article≈ 25 min
Pre-lab quiz (5 pts)8-question checkpoint (2 pts) and 3 discussion questions (3 pts)≈ 20 min
Lab activityAnalyzer calibration and fitting, then a graded treadmill test on two volunteers while the class records HR, RPE and stop criteria75 min
Lab notebook (15 pts)VO₂max criteria, VT1 and VT2, HR zones, measured vs ACSM VO₂, discussion≈ 60 min

Pre-Lab Reading ≈ 25 min

Every pre-lab has the same three parts: background reading, one article from the research literature, and the pre-lab quiz and discussion questions you submit before lab.

1. What the analyzer measures

Every breath, the analyzer measures how much air you move (flow, giving VE in L/min) and how much oxygen is missing from the air you breathe out. VO₂ is the volume of oxygen you take up per minute. A VO₂-only device measures O₂ and flow; a full cart also measures CO₂, which gives VCO₂ and the respiratory exchange ratio (RER = VCO₂/VO₂). RER tells you the fuel mix (0.70 = fat, 1.00 = carbohydrate) and rises above 1.0 at very hard intensities as bicarbonate buffers acid and extra CO₂ is breathed off.

2. Was it a true VO₂max?

A test shows a true VO₂max when VO₂ stops rising (a plateau, increase < 150 mL/min or < 2.1 mL·kg⁻¹·min⁻¹) even though the workload keeps climbing. Without a plateau, the highest value is called VO₂peak. Secondary criteria: HR within 10 bpm of age-predicted maximum, RPE ≥ 17, RER ≥ 1.10 (cart only), and blood lactate ≥ 8 mmol/L (optional, Week 5 skills).

3. Two ventilatory thresholds

  • VT1 (first ventilatory threshold, ≈ 50–65% VO₂max in most students): VE begins to rise faster than VO₂, and VE/VO₂ starts to climb from its lowest point. It is close to the lactate threshold. Below VT1 you can talk comfortably.
  • VT2 (respiratory compensation point, ≈ 80–90% VO₂max): a second, steeper rise in VE as breathing works to blow off CO₂ and offset rising acidity. Above VT2 exercise can be held only for minutes.
  • VT1 and VT2 split training into three zones: easy (below VT1), moderate/tempo (between), and high-intensity (above VT2). Write each as a heart rate so it can be used without an analyzer.

Interactive: Find the thresholds

Simulated ramp test. Drag your VT1 and VT2 picks to the two bends in ventilation, then reveal the answer. Switch the analyzer to "full cart" to see what RER adds.

4. Protocol you will use

PhaseTreadmillDurationPurpose
Rest (standing)—2 minBaseline VO₂ and HR
Stage 13.0 mph, 1%3 minWalking economy vs ACSM walking equation
Stage 25.0 mph, 1%3 minRunning economy
Stage 36.0 mph, 1%3 minRunning economy
Ramp+0.5 mph every minute from 6.5 mph, 1%to exhaustion (≈ 6–10 min)VT1, VT2, VO₂max
Cool-down2.5–3.0 mph, 0%≥ 3 minRecovery HR

Cycle ergometer alternative: 3 min each at 50, 100 and 150 W, then +25 W per minute (+20 W for smaller or less-trained participants) at 70–90 rpm. Use the ACSM leg-cycling equation for the economy comparison.

5. From the literature ≈ 15 min

Read this week

Montoye, A. H. K., Vondrasek, J. D., & Hancock, J. B., II. (2020). Validity and reliability of the VO2 Master Pro for oxygen consumption and ventilation assessment. International Journal of Exercise Science, 13(4), 1382–1401. pmc.ncbi.nlm.nih.gov/articles/PMC7523887/

Every analyzer, portable or cart, has to be checked against a criterion. This study shows how that is done and how much error to expect. Read it even if your lab uses a full cart.

Read for:

  1. What the device measures and what it does not.
  2. What it was compared with, and at what intensities.
  3. How large the differences were, and how its test–retest reliability compared with the cart.
Optional supplement: GSSI virtual labThe free GSSI University virtual lab Effect of Carbohydrate Intake on Exercise Metabolism & Endurance Performance shows how RER and fuel use change with carbohydrate intake over a long exercise bout. Use it to extend this week, as an alternative on a remote or weather day, or if your program has no analyzer. The carbohydrate model on the Interactive Tools page pairs with it.

Before you come to lab

  • Volunteers: complete the PAR-Q+ check with your instructor, and arrive having avoided caffeine for 3 hours, food for 2 hours and hard exercise for 24 hours. Wear running shoes and clothes.
  • Everyone: know your role (operator, HR and RPE, timer, safety spotter, recorder) and the stop criteria.
  • Bring your Week 6 field-test results for comparison.

Pre-Lab Quiz ≈ 20 min

Two parts, both due before lab (5 pts). Checkpoint (2 pts): eight questions on the background and the article; aim for 7 of 8 before you come to lab. Discussion (3 pts): three short written answers you submit to your course site.

Checkpoint

A VO₂-only analyzer (no CO₂ sensor) cannot report:
RER = VCO₂/VO₂, so it needs a CO₂ measurement.
In the last two minutes of a ramp, VO₂ rose from 3,410 to 3,450 mL/min while speed kept increasing. This indicates:
An increase under 150 mL/min despite more work is the classic plateau.
At VT1 you would expect to see:
Ventilation starts to outpace oxygen uptake, so the ventilatory equivalent turns upward.
ACSM running VO₂ at 6.0 mph and 1% grade is about:
S = 160.8 m/min; 0.2(160.8) + 0.9(160.8)(0.01) + 3.5 = 32.2 + 1.4 + 3.5 = 37.1.
A volunteer's VT2 occurs at a HR of 178 bpm. A "tempo" run between VT1 and VT2 should be done:
The zone between the two thresholds is the moderate (tempo) zone.
In Montoye et al. (2020), the VO2 Master was compared against:
The cart was the criterion measure for VO₂ and ventilation.
The mean absolute percent differences for VO₂ and VE overall were:
Acceptable for most uses, but large enough to matter when comparing two close values.
Compared with the cart, the VO2 Master's test–retest reliability was:
Repeat tests on the portable unit varied a little more than on the cart, which matters when tracking change over time.

Discussion questions (submit to your course site)

About 75–150 words each unless stated. Each answer is worth 1 point: correct physiology, specific to this lab, and in your own words. Cite the article (author, year) wherever you use it.

1. What is the difference between VO₂max and VO₂peak? Which criteria would you use to decide which one a test produced (a) with a VO₂-only analyzer and (b) with a full cart?

2. Predict the VO₂ (mL·kg⁻¹·min⁻¹) at 3.0 mph and at 5.0 mph (1% grade) using the ACSM walking and running equations. Show your work, and say whether you expect a novice runner's measured value to be higher or lower than predicted.

3. Using Montoye et al. (2020), explain how large a difference between a volunteer's measured and predicted VO₂max would need to be before you are confident it is real rather than measurement error.

Lab Activity 75 min

Organization

One analyzer tests about two volunteers per 75-minute lab (≈ 30 min each including fitting and cool-down). Ideally the volunteers also ran the Week 6 field tests. Every other student has a role, and the whole class receives both data files.

  • Analyzer lead: calibration, mask fit, starts and marks the recording
  • Treadmill operator: speeds and grades on the clock
  • Safety monitor: behind the treadmill, watches form and symptoms
  • HR/RPE recorder: HR and RPE in the last 15 s of each stage and minute
  • Criteria checker: calls the plateau and the stop
  • Observers: watch the live display and note where breathing changes

Equipment

  • VO₂-only analyzer (e.g., VO2 Master, with tablet/phone app) or metabolic cart; masks in several sizes; calibration syringe if required
  • Chest-strap HR monitor paired to the analyzer
  • Treadmill with safety clip; fan; RPE scale (6–20)
  • Disinfectant for masks and sensors (follow the manufacturer's cleaning instructions)
  • Optional: lactate analyzer for a post-test sample
📍 Set up for your campusVolunteers should be screened apparently healthy (PAR-Q+ cleared) and a CPR/AED-certified instructor must be present for a maximal test. With two analyzers, test four volunteers. With a metabolic cart, follow its warm-up and two-point gas calibration (often 20–30 min), so start it before class.

Timeline

  • 0:00–0:10Analyzer warm-up and calibration (flow and gas, per manufacturer); mask sizing and leak check; consent and screening of volunteer 1.
  • 0:10–0:40Volunteer 1: 2-min rest, three 3-min stages, ramp to exhaustion, cool-down. Recorders log HR and RPE; observers mark where breathing changes.
  • 0:40–1:10Volunteer 2, roles rotate. Volunteer 1 cools down and gives a recovery HR at 3 and 5 min.
  • 1:10–1:15Export both data files (CSV) to the course site; disinfect masks and sensors.

Procedure

  1. Enter the volunteer's age, sex, height and mass in the analyzer software. Fit the mask: no leaks when the volunteer exhales hard against a covered opening.
  2. Record 2 minutes standing still on the treadmill. Clip the safety key.
  3. Run the three economy stages, marking each stage change in the software. Record HR and RPE in the last 15 s of every stage.
  4. Start the ramp at 6.5 mph and add 0.5 mph every minute. Record HR and RPE each minute. Give steady encouragement.
  5. Stop when the volunteer signals or cannot keep pace, or for any stop criterion (chest pain, dizziness, unsteady gait, abnormal symptoms). Slow to 3 mph for at least 3 minutes; keep the mask on for the first minute of recovery if you want recovery data.
  6. Save and export the file. Record peak speed and total ramp time.

⬇ Backup data set (2 participants)

Lab Notebook ≈ 60 min · due at the start of next lab

Step 1 — Clean and summarize the data ≈ 15 min

  • Average VO₂ over 30-s windows to smooth breath-by-breath noise: =AVERAGE(J2:J4) for 10-s rows. VO₂max (or peak) = the highest 30-s average.
  • Economy: mean VO₂ (mL·kg⁻¹·min⁻¹) of the last minute of each 3-min stage vs ACSM prediction; % difference =(measured-predicted)/predicted*100.
  • Plateau check: change in VO₂ over the final minute (mL/min). With a cart, also peak RER.

Step 2 — Figures ≈ 20 min

  • Figure 1: VO₂ (mL·kg⁻¹·min⁻¹) and HR vs time, with stage boundaries marked.
  • Figure 2: VE vs VO₂ (or vs time), with your VT1 and VT2 marked. With a cart, add VE/VO₂ and VE/VCO₂ vs time.
  • Table 1: measured VO₂max vs the volunteer's Week 6 Cooper and ACSM estimates; HR at VT1 and VT2; three training zones in bpm.

Step 3 — Discussion ≈ 25 min

  1. Did the test reach a true VO₂max? Justify with the criteria your equipment allows.
  2. Where were VT1 and VT2 (time, %VO₂max and HR)? Describe the physiology behind each threshold and give the volunteer's three training zones.
  3. How closely did the ACSM equations predict measured VO₂ at each stage? Give two reasons a person's economy differs from the equation.
  4. How did measured VO₂max compare with the Week 6 field estimates? Which estimate was closest, and why?
  5. What can a full metabolic cart tell you that a VO₂-only analyzer cannot, and when would that matter for a client or athlete?

Grading rubric (15 pts)

CriterionPtsFull credit looks like
Data processing430-s averages, VO₂max, economy vs ACSM, plateau check
Figures & table4VO₂/HR vs time; VE with VT1/VT2 marked; predicted vs measured table with zones
Discussion6All five questions answered with numbers and correct physiology
Presentation1Clear, labelled, units throughout